不同降雨入渗条件下预应力锚索加固边坡稳定性分析

为了研究不同降雨条件下边坡安全系数及预应力锚索轴力变化规律,以省道S303沿线某边坡为研究对象,考虑土体饱和-非饱和渗流与非饱和强度理论,基于有限元分析,对不同降雨工况下的孔隙水压分布、锚索轴力及采用强度折减法计算的边坡安全系数变化规律进行了研究。结果表明: 降雨量一定时,降雨入渗范围随雨强增大而减小,暂态饱和区域随雨强增加而增大; 边坡在加固前后的安全系数均随降雨量增加而不断减小,采用预应力锚索加固能有效提高边坡安全系数,并减小降雨对边坡稳定性的影响; 随着降雨量增加,各锚索轴力均增大,当降雨量一定时,雨强越小,对应的锚索轴力提升幅度越大,靠近底部的锚索轴力对降雨最为敏感。     

煤矿井下风水管路压力在线监测系统的研究与应用

为提高井下管路供风、供水的安全性、可靠性，以工业环网作为网络通信平台，通过分站采集数据上传至地面，实现对煤矿井下供风、供水管道的远程实时监控及远程控制，及时发现管网故障，提高维护效率、降低损失，保障供风、供水质量，达到科学预警、降低成本、提高效率的目的。     

油藏中后期减氧空气驱提高采收率机理研究

尕斯库勒油田E¹₃油藏已经进入高含水时期，储采失衡加剧，综合含水率达到了80%以上，原油产量下降，经济效益变差。为了提高油藏原油采出程度、改善油藏开发效果，调研了国内外减氧空气驱的机理研究以及现场试验的资料，建立了以油藏真实孔渗饱数据为基础的一维条形地层机理模型，并选取该油藏Y12-27井组进行了减氧空气驱可行性验证。研究表明:纵向顶部减氧空气驱驱油效果优于水驱和氮气驱；驱替压力对原油采出程度影响不大；注水转注气可以提高原油采出程度；对于减氧空气驱，由于低温氧化反应的作用，氧气浓度对原油采出程度有一定影响，但比较微弱，其中，氧气浓度为10%时，驱替结束采出程度最高；尕斯库勒油田E¹₃油藏属于注水开发“双高”油藏，适用于减氧空气驱；对于该油藏Y12-27井组，顶部减氧空气驱驱油效果好于水驱和氮气驱，建议氧气浓度超过10%时采取关井等措施。     

一种新型包装专用蜡的研制

为了根据某瓦楞纸箱生产厂的实际生产条件制备一种耐热、耐低温、防水、透气等性能优异的包装专用蜡，将58号全炼蜡和70号微晶蜡混合物作为基础蜡料，分别考察添加剂、助剂、抗氧剂等对基础蜡料滴熔点、运动黏度及外观等的影响，确定了最佳制备配方：合成蜡、添加剂B、助剂1、助剂2、抗氧剂加入量（w）分别为基础蜡料质量的9.8%，6.5%，1.5%，2.1%，0.1%。在温度为160 ℃、时间为30 min、搅拌速率为200 r/min条件下制备的包装专用蜡具有熔点高、黏附性强、光泽性好的优点，满足该瓦楞纸箱生产厂的质量和外观要求。     

基于危险源的水利工程施工全过程安全管理研究

水利工程的特殊性,决定了其在安全管理构建中更加注重全过程管理机制的构建,以及危险源下的精准安全管控。在传统安全管理模式之下,水利工程安全管理盲点多、效率低,不利于全过程安全管理的高效实施。文章立足水利工程的危险辨识,分析了水利工程危险源全过程安全管理中的问题,并在此基础之上,从强化危险源精准辨识、构建危险源动态管理机制、优化危险源评价工作、加快危险源信息库建设等方面,具体论述了危险源下水利工程全过程安全管理措施。     

Simulation Study on Hydrogen-Heating-Power Poly-Generation System based on Solar Driven Supercritical Water Biomass Gasification with Compressed Gas Products as an Energy Storage System

Supercritical water gasification driven by solar energy is a promising way for clean utilization of biomass with high moisture content, but direct discharge of liquid residual causes energy waste and decreases energy efficiency. To reduce energy waste, a poly-generation system for hydrogen-rich gas production coupling heat supply and power generation based on supercritical water gasification of biomass driven by concentrated solar energy was established in this paper, which also provided a novel energy storage method to overcome the shortcomings of solar discontinuity. Thermodynamic model of the system was proposed and life cycle assessment(LCA) of the system was conducted. Influence of different parameters(temperature of 600℃ to 800℃, outlet temperature of heat exchanger of 42℃ to 56℃, biomass slurry concentration of 5% to 6.5%) on the gasification performance, energy and exergy efficiency, energy distribution and global warming potential(GWP) was discussed. The results indicated that hydrogen yield increased as gasification temperature increased since free radical reaction was enhanced which gas production reaction was classified into. Molar fraction of hydrogen increased as gasification temperature increased and reached 65.6% at 750℃. Energy and exergy efficiency of the system reached 74.84% and 34.87% at 700℃ and 600℃ respectively and that of gas production was 18.15% at 650℃, which was the highest. Increasing reaction temperature and decreasing biomass slurry concentration were effective ways to decrease GWP. Optimal operating parameter was reaction temperature of 650℃, outlet temperature of heat exchanger of 50℃ and biomass concentration of 5%.     

松木颗粒热解与高温蒸汽气化半焦产率及形貌特征分析

以成型松木颗粒为原料，进行低温热解，研究了热解温度和升温速率对生成的松木半焦产率及官能团的影响。以试验得到的松木半焦进行蒸汽气化试验，对比分析了温度对半焦重整气化形貌特征、比表面积和平均孔径的影响。研究表明：随着热解温度升高，松木半焦脂肪族结构峰消失转化为烃等小分子物质及气化气，进而降低半焦产率。升温速率升高，半焦产率呈先下降后升高的趋势，在800℃升温速率为30K/min时半焦产率最低。不同温度热解和蒸汽气化对比试验表明，温度相对较低时（500℃）热解和蒸汽气化半焦孔隙结构相近，随着温度的升高，蒸汽气化半焦结构发生明显变化，900°C时出现了更小的孔道结构且比表面积增加明显。蒸汽引入使松木半焦和水蒸气发生热解反应的同时发生了脱氢反应，气化半焦形貌出现熔融和烧结现象。     

Experimental investigation on gasification characteristics of polycarbonate (PC) microplastics in supercritical water

In order to solve the problem of marine microplastics and realize the harmless resource utilization of plastics, the gasification experiments of polycarbonate (PC) microplastics were carried out in supercritical water and a novel seawater gasification of microplastic experiment was investigated. In this paper, the effects of different operating conditions (temperature, time, feedstock concentration, pressure) on gasification performance were discussed. The gasification kinetic of microplastics in supercritical water was calculated. The experimental results showed that the increase in gasification temperature and time enhanced the cracking reaction and free radical reaction of the microplastics to increase the gasification efficiency, while the reduction in feedstock concentration improved the gasification efficiency by increasing the gasification level of unit feedstock. The change in pressure had no significant effect on gasification due to the fact that the properties of the supercritical water were not significantly changed. It was found that the valuable results that all alkali metal salts in seawater promote hydrogen conversion, while in terms of carbon conversion, only KCl, CaCl₂, NaHCO₃ and seawater had a significant catalytic effect on the gasification. Seawater gasification of microplastics was a potential resource utilization method. Finally, it was considered that the PC plastic gasification conformed to the random nucleation and subsequent growth model (n = 3), and the reaction activation energy was 230.45 kJ/mol, which was smaller than that of traditional pyrolysis.     

多晶硅生产中残液搅拌罐密封结构的改造

在处理多晶硅生产中产生的残液时,残液搅拌罐填料密封出现泄漏,针对此问题提出了优化措施,达到了预期效果。     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。